even more pictures
 

The first is the holding tank compartment, then the generator compartment, the 6' storage compartment (Mikes bedroom) and a shot of the floor framing.

entry door
 

Yesterday my sister came out and helped me trial fit the entry door. It felt good to see the door on the truck and that it fits. I can now build the upper door frame with confidence.

looking good.

Huh ... first there was door, then a frame. Rather than building a frame and then the door. Learn something every night.

Looking good. I really like your steps. Mine were built in the inside of the coach and they eat up a lot of floor space.

Do you have any pics of yours Andy?

I can get a picture or two. I do not have any exterior steps they are built inside. I don't have to remember to fold up my steps but therr is also a big stair pit inside of my rig. Give & take.

Here are some pics of the steps

one suggestion on the (interior) steps before you finish them....they make a GREAT place for "hidden" storage....Hinge the step/tread - it makes a great place for folks to throw their shoes and it keeps the dirt down / reduces interior carpet wear too !

Ken, can you send some pics close up of your entry steps, they look great, did you fab them or purchase them? thanks, Pete

steps
 

Pete, the outside steps are Kwikee electric steps. You can find them online. They extend out from the body about 27" and the bottom step is about 10" off the ground. I think they have an 8" rise. I built the inside steps. I have a two step Kwikee electric that I bought thinking it would be the correct height and then discovered a three step would work better. I would make you a good deal on the two if it would work for you. The two best pictures of the steps show the steps out and then in. When in mine are 8" above the bottom of the bodywork, which is 15" off the ground. I hope that helps.
Kenn

waste dump valve
 

Today I made an adapter for the waste dump valve. I used aluminum so I can weld it to the bottom of the holding tank.

Wow! Did you machine that out of billet aluminum? What about aluminum and the corrosive stuff in the tank? I suppose if the tank is aluminum, then its fine for this piece to be aluminum. Do the insides of the aluminum waste tanks corrode badly? I hadn't thought about it until right now.

Nice work.

nice to have or know someone w/ a CNC machine !
i thought i was lucky knowing someone w/ a metal lathe ;)

great question
 

90-GTSC when I got home late lastnight from bowling, I saw your question about the aluminum holding tank contents being corrosive. I got a sick feeling in the gut and then spent some time on the net trying to find information on aluminum and corrosion. At 8 am I called my aluminum supplier and put a hold on the order I made on Friday for cutting and floding $370.00 worth of .125 5052. You may have saved me $370.00. If it turns out that the aluminum won't work, then I just spent a day using the lathe to make the adapter to mount the dump valve. I like when people ask questions. I will spend what ever time it takes to educate myself on the subject. I will include a picture of my made in China lathe and my friend making an oil pan for his race car on my used mill I got at an auction. Keep the questions coming. Thanks again Kenn

I just pulled this from the Liberty Coach web site:

"Metal fresh water and holding tanks, specifically stainless steel and aluminum, instead of plastic with reduces greatly the odor and bad taste."

Do you think stainless steel for the gray and black with aluminum for the fresh? Or stainless for the fresh and aluminum for the gray and black?

What do the NRC, Showhauler, and Renegade guys have in their coaches?

Mr. Hawk ... what do you put in your coaches for the water tanks?

BTW ... check out this video from Liberty Coach web site. Frank Jr. is at the Florida RV Super Show show in Tampa this week in their $2.3 million coach!

Florida RV Super Show | Custom Coaches-Liberty Coach

Dick

Ive got:

1 - 65 Gal Black Plastic Gray Water Holding Tank
1 - 65 Gal Black Plastic BLACK Water Holding Tank
2 - 110 gal PLASTIC (clear/white) Fresh water Tanks

My gray and black holding tanks are both black plastic of some sort.
My fresh water tanks are kind of white plastic, barely able to see through it enough to see the water level inside it.
Same material as Don's but different quantities.

I spent 3 days last october in the Elkhart area going thru rv manufacturers and truck conversions company's and everyone was using black plastic waste tanks and white plastic fresh water tanks.
shorts

my bet is -

1) PLASTIC is CHEAP
2) Plastic is LIGHT
3) Plastic allows for expansion & shrink-age
4) FOOD GRADE plastic is less prone to corrosion

What to make the holding tank out of????
 

After three days and nights of looking on the net and talking to many people, I have decided to give up the idea of using aluminum. I now plan to build a tank out of plywood with several coats of epoxie. In my search I found ready-made tanks that were close in size but either would not hold as much or were to big to fit my space. I have built many things using wood and epoxie so I know what is ahead of me. I once built gas tanks for a flat bottom boat back it the day. Anyway I did learn that if you need a custom size you need to build it. I always though the big builders used plastic to save money and did not want to spend the time and money to build one out of amuminum.

Kenn, what about building the tank out of aluminum and then coating the interior with some type of protective coating, This is pretty much what they do with aluminum drink cans. Would think that an epoxy or perhaps a corrosion coating such as NO-OX-ID (NO-OX-ID rust preventatives & conversion coating prevent corrosion) could be applied to the interior thru a removable hatch in the top or poured in and then roll the tank around to coat it and drain out the excess. not sure how that would compare cost wise or durability in the elements compared to a plywood tank. I would be afraid of moisture working its way into the plywood from inside or outside and causing delamination or rot. Then again I am way to type A and tend to over think everything lol.

epoxy/wood vs aluminum/????
 

Dave great minds do think alike LOL. I spent many hours trying to find a product to paint the inside of the aluminum tank. Some concerns I had were not just the tank walls but the aluminum adapter I made. If I coated the adapter with epoxy, it would add enough thickness that the rubber seal would not fit as it should. If I machined the adapter to make room for the epoxy, it would make for a very thin (read weak) part. I checked into pour-in type products and found most are for steel and very little information on aluminum. I am not to worried about water getting to the wood. I will be able to get to all side and the bottom of the tank after the coach is done. If an aluminum tank developed a leak it would have to be removed to make a repair but the wooden tank could at least be glassed over on the outside to get me home. I have used epoxy with good results on many project including boats (gas tanks & and many other areas), race cars body, wings and lots of parts. Yesterday I cut all of the plywood and today I will start on the epoxy. I plan to lay all of the sheets flat and roll and brush the epoxy on before I glue it all together. When the tank is glued together I will do the outside. I really wanted to make it out of aluminum. At some point I need to move on and being the only decision maker I thought the wood/epoxy made the most sence. I will post pictures as the tank develops. Thanks for your thoughts, I do appreciate them. Kenn

What kind of plywood? Marine grade?

I have heard of folks building plywood tanks and lining them with fiberglass and it worked OK. Be sure to make the box strong because water is heavy. Containing that water takes a bit of strength when it starts to slosh around.
P.S. I'm not convinced that there would be a problem with aluminum.

plywood tank
 

I am using 15/32" exterior grade from Lowes. I am using three layers of 9 once cloth on the inside and two layers on the outside. The inside joints will have an adhesive fillet shaped with a spoon and covered with more cloth. The outside joints will have several layers of cloth. I am installing a tank monitor system made by Tech-Edge Manufacturing in Sweethome Oregon (541) 610-3116. This is a system that mounts foil tape on the outside of the tank and reads through the tank wall. I will be putting the tape on the inside of the tank and running the wires to the outside. The foil tape will be glassed over on the inside.

Sounds like a good plan. I have done lots of similar work with West Systems epoxy and glass. You are going to need to do something to rough up the surface at the corner jounts since you will have already glassed the inside of the individual plywood sheets. Peel ply is supposed to be an easier way to go but I always just go at it with an auto body disk sander to knock off the shine. The corners need to be extra strong. All that weight will try to bulge out the sides and convert any cube to a sphere.

Tech-Edge monitor
 

Today I epoxied the aluminum strips and copper pads to the inside of the end panel. I drilled a hole and then made small cuts with a hand saw to pass the copper pads through without cutting any wires. I stuck the sensor module to the outside. I used 3" cloth tape and then 4" cloth tape followed with a full layer of cloth. No if I ever needed to change out the sensor it would be possible without going inside the tank. Next up is all of the inlets 1 1 1/2" vent, 2 1 1/2" drains and a 3" toilet going in with a 3" dump valve going out.

tank is taking shape
 

I have been working on the inlets and the outlet for the holding tank. I used stainless thread anchors on the floor of the tank to recieve the 1/4 20 bolts that hold the dump valve to the underside. I used epoxy (thickend) and several layers of cloth on the inside. I will use a good marine sealant on the outside. I made fiberglass flanges to mount the rubber grommets that will hold the abs drains. Today I epoxied the baffel in the center. I will use cloth on the glue joints and then be set to glue the top and bottom on. This has been a big time eating part to build. On the good side it will hold 80 gal.

more pics
 

More pictures.

the tank is done
 

Yesterday I epoxied the drain line flanges to the tank. Today I spent some time trying to clean the shop. I clamped the tank in place and cut, welded, drilled and bolted the mounts to the floor joists. It just fits and fills the compartment except for 8" between the back of the tank and the rear body. The tank ended up weighing 80 LBS and it should hold 79 gallons. I need to drill two more holes after I remove the tank and lower mounts. The tank will have 1/8" rubber between it and the mounts on all sides. I am glad to be done with the tank that was a lot of work.
Tomorrow I will start cutting and welding 2 x 2 for the roof frame. I plan to tack weld it to the floor frame and remove them together. After painting the lower unit and truck I will cut the tack welds and lift the roof add the wall studs.
We have been having rain and snow for a while but tomorrow is going to be sunny so I might move the truck outside and try to clean the shop better.

more welding
 

Today I finished cutting and welding the roof framing. I used .095 2" x 2" on 24" centers for the roof and the floor is .120 2" x 2" on 16" centers welded to the 4" chanel iron. On top of the .120 2" x 2" is .120 1" x 2" laying flat. The first picture is from the rear on the passenger side. Pictures 2 & 3 are showing the roof and floor frames. You can see the 14" frame for the bathroom vent. The last picture is showing how I will store the holding tank until it goes back on the rig. Next up is to cut the tack welds between the two lower sections and lift the top two sections off the truck. I might hang them from the overhead to keep them out of the way.

Hi Kenn, you have made some real progress, its looking great. For those of you following along at home, my wife and I had a chance to visit Kenn and see the progress on his build personally a couple of weeks ago. This man is doing an amazing job of his build. The truck totally fills his shop, and yet he has found a way to be organized and is efficiently working on a well thought out quality build. Really helps to motivate those of us still stuck in the armchair phase of our builds lol. Thanks again for your hospitality Kenn, and I look forward to pictures of your continued progress, and to my next opportunity to visit with you.

Dave

Motivation
 

Dave thanks for the kind words. Your visit has motivated me to keep plugging along. You asked a lot of good questions. I have been spending time in the planning of the sidewall (FRP) installation. I will clamp one sidewall to the frame and drill .5" holes at four places in the roof frame. I will use .5 steel rods 10' long and run the rods from one side to the other with about nine inches sticking out on each side. Now I will be able to hang the FRP from the rods while I add the glue to the wall studs and frame. After both sides are glued and screwed to the frame I can pull the rods out and fill the holes in the FRP.

fender wells
 

Today I finished the rear fender wells. I started with 32" x 68" 14 ga steel and had the supplier bend a 90 degree bend at 17". I end up with a 17" vertical piece and a 51" horizontal part that covers the tires. The drivers side is 9" longer. The front rest on top of the compartment frame in front of the tires. I made small angle iron tabs with a 1/2" lock nuts welded to them. I drilled holes in the sheet steel and bolted into the tabs and then welded the tabs to the floor joist. I can remove the fender wells from below. I bolted the bottom of the 17" (back of the fender well) piece to the mud flap mount with four 3/8 bolts. It all went as planed but an extra set of hands would have been good. I hope you can understand the pictures. Just a few more things befor I remove the roof and floor framming.

sheet metal work
 

Yesterday I finished fabricating a storage space for my shore-power cord. I used a six inch deep area above the exhaust to save room in the compartment. It was a three day project that included a lot of drilling, welding, sheet metal cutting and head scratching. I think it will work pretty good. I mounted the rubber fender lips and started making a filler plate to cover the eight inch hole below the entry steps when they are retracted for travel. Yesterday was the first day without rain or snow in about a week so I was able to move the truck outside and get better pictures. Next up is to mount the camper frame to casters and store it outside until later. Once the camper frame (floor & roof frame) is out of the way I will remove the lower unit and start getting it ready to paint.

I presume the cord will go in the 6" deep area above the exhaust. With the exhaust below, won't that area get awfully warm? Will the 6" area be open to the compartment next to it? or will there be a cover of some type.

Keep up the good work.

Kenn ,where did you purchase your rubber fender lips?


Thx, Patrick

questions
 

# 90 , yes the cord will hang in the area above the exhaust. I will wrap the exhaust pipe with a heat insulator that I have used on race cars. The cord will be open to the compartment. I might make a roller for it and pass the end of the cord through the side of the body.
Patrick, I got the rubber fender molding from Esley Truck Accessories located at 8983 Truckman way, Salem Or 97303 phone 1-800 547-3667. They carry two types. The one I used mounts to the outside of the body and the other mounts to a lip around the wheel opening. They are sold by the foot $2.75 for the one I got and $4.50 for the other.

This is awesome. Wow!