Suggestions on Interior Walls
1 Attachment(s)
This is a great site!
I plan to start an internal fit-out of a 14' FRP Morgan cargo body attached to a Fuso FG 4x4 and I'm in need of advice on how to finish the interior walls in the attached photo. Does anybody have suggestions as to how to mount paneling to the steel studs? Should I mount wood strips to the steel studs and secure the paneling to them? I'm sure there's going to be more questions forth coming as the job progresses. Thanx in advance! |
1 Attachment(s)
We use Panolam 1/4" nylon rivets we got at Lowes. In the pic they are hard to see. We only used 3 per panel there because the steel was on 2' centers. We also used their corner and divider trim. We used double sided tape and construction adhesive behind them. Both worked but the tape is easier. Same with the ceiling. Windows, cabinets, door frames and interior walls will also help support the paneling.
|
RLPRACING
Thanx for responding! I reviewed some of your posts about your build...AWESOME! So I take it you applied the adhesive along the length of the steel studs only and not to the foam panels? Where the seams of the panels came together, did the divider strips fall somewhere between the steel studs? When you hung your cabinets, did you use toggle fasteners into the steel studs to secure them? I've been thinking of using white FRB panel in the ceiling, but my reaearch uncovered recommendations not to do so. What maternal did you use? |
Quote:
Going back to your original post you asked about putting wood strips on the steel. If you were to do that, it may insulate that area a little better than ours. When its zero degrees outside, that cold goes right through our skin and steel stud and all we have is that thin wall board to kind of stop it. You can feel where every stud is. Keep the questions coming! |
2 Attachment(s)
To reduce the temp transfer thru the studs I lined the inside of mine with 17/32 plywood. I then glued the FRP to that. I used it on the entire interior. FRP is easy to clean,durable and does not absorb odors like some materials. I guess it all depends on how you are going to use it and what you want it to look like.
Michael |
2 Attachment(s)
RLPRACING & mmmc101
Keep the suggestions coming, I'm open to all thoughts and ideas. The plan was to attach some wood strips/studs flush along side the steel studs, not on top of them. Then secure a layer of plywood to the wooden studs using glue and staples and using the steel studs to support the bed frame and any wall mounted storage bins I might place around the living space. The original plan was to fit out the interior like the attached photos using a cloth covered panel for the walls. I kinda like the white/gray/black color scheme. Would a trip to a RV surplus store prove fruitful regarding the gray cloth covered wall panels? |
Before I went with the FRP, I obtained several samples from a local upholstery supplier. They had vinyl, cloth and foam backed materials of all kinds. They also stocked the materials needed to install it. Just another option.
Michael |
2 Attachment(s)
Quote:
Here's some Sketch-up views of the exterior. |
"Would a trip to a RV surplus store prove fruitful regarding the gray cloth covered wall panels?"
I found the selection to be low so it would be better to call a few and ask what they had in inventory if you have very far to drive. I like your wood stud idea and should work great. Plans look great! |
I just wanted to add my $.02 regarding lining the walls with fabric...
We have found that no matter how sealed, or pressurizing the box while long dirt road drives... You interior will get a little dusty. Thus, hard sided walls made it easier come "clean-up" day. Hard sided walls also don't collect cooking smells and moisture if you plan on going to tropic environments. |
Quote:
Did you use inside corner trim where the FRP ceiling panels joined the FRP wall panels? |
1 Attachment(s)
No I did not use the FRP corner trim. Didn't like the looks of it. The ceiling/corners will be trimmed in red oak and stained to match the cabinets. I did use the FRP trim between the ceiling sheets. (seen in photo's).
MMM |
|
Quote:
https://www.truckconversion.net/attac...97b55b6c3a.jpg |
that rear window (?) in yellow...over the storage door....is there a way to line it up w/ either the storage door or the other window (closer to the entry door) ? it might look a little nicer if things were aligned.
|
Quote:
|
looks like your really getting a ton accomplished... and it looks great! keep the pictures and questions coming...
|
Quote:
Most of the effort so far goes to a local builder of mobile event trailers. I don't have the luxury of a large staging area out of the weather to do the exterior shell work myself. The dinette will be placed at the concession window opening. Its hard to see but there's a window installed within the concession window, but its the wrong size. They discovered the error and plan to make it right. https://www.truckconversion.net/attac...55c36b15bb.jpg |
All times are GMT -5. The time now is 04:28 AM. |
Powered by vBulletin® Version 3.8.8 Beta 1
Copyright ©2000 - 2024, vBulletin Solutions, Inc.