Truck Conversion & Toterhome Community

Truck Conversion & Toterhome Community (https://www.truckconversion.net/forums/)
-   Coach In The Making (https://www.truckconversion.net/forums/f103/)
-   -   I get a "DO OVER! " (https://www.truckconversion.net/forums/f103/i-get-do-over-7336/)

Schiada 09-20-2014 07:50 PM

I get a "DO OVER! "
 
Hello all.
This will be my DO OVER build. This truck was started sometime in 2002. At the time I was in Offshore Racing and wanted a truck that would go up the Grape Vine ( I 5) faster than the gas trucks I was using. I would get passed by almost everything !

But their were, what looked to be loaded semi's that must have been doing 65 +.:eek: I knew that was the way to go.

So I started looking for a tractor. Then I would find a box and stretch the chassis to fit.

As it turned out their was a semi that was used in a Movie ( 8 legged freaks ) that was for sale. Think it was $4000 but their was a little fire damage ?

https://www.truckconversion.net/attac...7c669b30b5.jpg

But all in all it could be fixed. Only takes money ! :rolleyes: Their were some magnesium parts that helped the fire keep going. Don't think think the Globe,AZ fire department was ready for that !:eek:

Schiada 09-20-2014 07:52 PM

https://www.truckconversion.net/attac...72af9b9360.jpg

Cab was ok but every thing under it was melted,big time.

So on with the story. Fixed the semi problems from the fire and found a box and got some used rails from another wreck to stretch the chassis to fit. Started the box work,sewer system, Gray water, water . Wiring A/C and DC in the walls,all the stuff . Oh and the new drive shaft system.

https://www.truckconversion.net/attac...19d334bd9b.jpg

Here is a photo of the box van it would replace.

https://www.truckconversion.net/attac...da8cfc58b1.jpg

Then I got some very bad news ! My Dad passed ! I felt like I was hit by a TRUCK ! Then 60 days later my Mom was gone also !

So I made the first trip with the truck to close out my family's home. A dark time and a long trip. 4500 miles and I had never driven a truck of that size before. Steep learning curve !

After all of this I started looking at my life and started to pull back. No more Offshore Racing , Road Racing just stopped ! Every thing went on hold.

Randy

Schiada 09-20-2014 08:12 PM

Time heals all ! And I'm starting the build back up.:D
She is a 1992 International 9600 COE. 350 Big Can Cummins with only 880,000 miles +-. 225 HP ( I'm told that can be upped but going to get my Family's stuff ,never felt like I needed more.) We will see. It scaled at 17,800 # with the stuff and pulling a car trailer and a car on it. She is a "X" McLane truck and went from Phoenix to some where in Texas its hole working life. Has a 10 speed trans.

This the general plan. Add 4 slide outs and finish what I started.

https://www.truckconversion.net/attac...d3bd7ce7c1.jpg

Here is a photo take today after being washed and sitting for 8 years ! (I do run it once a month. ) And I have a solar charger on the battery bank.

https://www.truckconversion.net/attac...2190fac093.jpg

In the photo is my Ranger 20' that will spend some time behind her. And in the plan is a lift to carry a Polaris RZR 800 for getting around when on the road.

Randy

RLPRACING 09-21-2014 08:58 AM

Welcome back and good luck. Above all, have fun!

Schiada 09-21-2014 10:30 AM

Thanks RLP. Been looking over your build. Very nice !
Randy

Schiada 09-23-2014 08:31 PM

Been pulling the old panels to see what it will take to install the slide outs.
Think I will add a steel frame for the opening and bond and rivet it ? After looking a other builds I think maybe I should have not used a old 20' box. But that is what I have and it will do. LOL

Also have a shot of the pass through. With my truck being a COE the pass through is part of the box.

https://www.truckconversion.net/attac...955a2b84e9.jpg

https://www.truckconversion.net/attac...3ecceb7c35.jpg

Randy

Schiada 09-23-2014 08:51 PM

Also been looking at Barker Cog slide outs. Ideas ? anybody worked with them ? The others are slow to return calls. It is making me wonder ? Guess I'm to small time ? Only need 4 slide out systems.;)

https://www.truckconversion.net/attac...c358f6094b.jpg


Also what skins for the slide outs ? Alum or Fiberglass ? The frame for the slide outs will be steel 1 1/2" x 1 1/2" 16 ga. tubing.

Could anybody post some photos of the building of the "box" part of the slide out ?

Barker Slideouts

Randy

hot rod 09-23-2014 10:44 PM

I would definitely be planning on additional structure in the walls around the slides. I looked at box trucks as a potential basis for a build like yours, and the wall constructions seemed geared more towards light weight than max interior width than strength. I'm just assuming the weight of the slide out hanging 3' off the side of the truck has to put serious strain on wall supporting it. Along the same vein I'd be thinking light weight construction on the structure of the slide itself. Being basically a rectangular box it should be pretty strong just on the geometry and not have to get carried away with heavy tubing.

Schiada 09-23-2014 11:46 PM

Hot Rod, What I saw in the Liftco wall mount got me thinking it may not be the right unit. The van box I have is good for keeping things on a pallet from moving around but their is not much their.

But using the fixed mount ,like the Barker. It would put little load on the wall. If I see it right the load would pass,for the most part into the floor and then to the chassis through the arms? Well I think ?

The frame of the floor of the box is a steel grid made up of 'I' beams on 16" centers. Think they 3" and are welded to the 2 center ,6" 'I' beams that run the length of the box. The floor of the box is 1 1/4" hard wood. Also the center wall will be load bearing. Should keep the center of the van box from spreading. A nother idea ?

With some planning and luck I should be able to mount the slide rails in between them ? Well at least that is the plan .

Will know more when I get the drawings and spec. from them.

Randy:confused:

Schiada 03-18-2015 01:58 PM

Well I'm back at it.

Going to pull back from the slide-outs . Poor input from manufacturer . I will just design and build one later . And their $$$$ ! Over priced for my way of thinking.

Been talking with my Wife and she felt the original setup was to small.( Food prep area) And when I started it was going to be used for short trips. (not very far-sited ).

Also going to move it to the other side of the box. With it moved my plan is to make the driver side a slide out in the future.Thinking a 8' x 36" x 6'6" +- ?

Pulled the walls and then on to the floor and the old counter.

https://www.truckconversion.net/attac...28b3643727.jpg

https://www.truckconversion.net/attac...a5a29341c9.jpg

I never really finished the inside so some things need to be redone.But its all good . I have a better idea now which will help.:o

Randy

Schiada 03-19-2015 03:21 PM

Go all the temp counter our and ready to pull the floor cover. Going to lay down a different cover. Some kind of hard wood ?

https://www.truckconversion.net/attac...a299e8ea12.jpg

Left the wires all installed so I can use the out lets till is time to rewire.

What is good to use to make walls ? 1/8" paneling ? What have you used ?

Randy

asitool 03-19-2015 05:56 PM

I've seen people use 1/8 or 1/4 paneling. Depends on whether you're going for a solid feel or reduced weight. I'm using 3/8 on the build I've got going now.

Schiada 03-19-2015 10:00 PM

Here she is in the bay.

https://www.truckconversion.net/attac...7711ab6e2f.jpg

Been working on the side windows. The wall moves way to much so I am going to put a reinforcement at the top and bottom to tie the cut uprights to the uncut ones.

The 1x2 is where the tubing will go.I will rivet/glue the tube to the skin of the box.

https://www.truckconversion.net/attac...56913775c9.jpg

Randy


About the walls. I think I will go with 1/4" of something.

Schiada 03-21-2015 02:00 PM

Got the reinforcement installed on one window.

You cut out the part. Install and drill all holes. After drilled remove and install sealer/bounder and hold in place with clecos and rivet.

I used SS rivets , the thinking is that the new steel rinforsment would eat up a Alum ?

https://www.truckconversion.net/attac...4ae6c13091.jpg

https://www.truckconversion.net/attac...7761cc84d5.jpg

https://www.truckconversion.net/attac...33179877df.jpg

Randy

Bob86ZZ4 03-21-2015 02:15 PM

Looks good, Randy. Keep the posts/pictures coming. I love watching other people build stuff since I'm not capable of building anything myself.

Schiada 03-21-2015 06:02 PM

Hi,Bob.
You bet, I may not do it the right way but I try.

Anybody that has a better way, let me know ! I can always use help.
Randy

hot rod 03-21-2015 06:39 PM

I've always used 3/8" plywood on the walls of my stuff. Not that much more weight in the larger scheme of things, and makes the wall nice and solid. Plus heavy enough to screw things to the wall and be sturdy.

Schiada 03-21-2015 07:50 PM

Wish I could find some "good" 3/8" ply. The big box stuff looks like hell.

But your right. I will keep looking.

Schiada 03-22-2015 10:18 AM

Here are some shots from the in side. The flash on my phone cant outdo the light from the window. Need to take a real camera ?

The glue is called metalbond. I used denatured Alcohol to clean things up before installing.

https://www.truckconversion.net/attac...5a99a33d0b.jpg

https://www.truckconversion.net/attac...bdb1e450e0.jpg

Randy

38Chevy454 03-23-2015 09:29 AM

I like your changes, and keeping the wife happy is always a good thing!

The metal bonding adhesives are pretty amazing how strong the bond is, don't think you will have any problems. A little extra reinforcement never hurt.

On the SS vs steel rivets. From a galvanic corrosion standpoint both are "protected" by the alum, or in technical terms the alum is anodic to the steel or SS. But for any real corrosion you have to have an electrolyte, usually water serves this purpose, and so between the sealer and the coated alum frame you will not have much chance. The bigger advantage is the SS will not rust due to general corrosion, or just basic corrosion of the rivet itself. The SS will stay shiny, whereas over time the steel could get some rust.


All times are GMT -5. The time now is 12:47 PM.

Powered by vBulletin® Version 3.8.8 Beta 1
Copyright ©2000 - 2024, vBulletin Solutions, Inc.