Truck Conversion & Toterhome Community

Truck Conversion & Toterhome Community (https://www.truckconversion.net/forums/)
-   Building Your Own (https://www.truckconversion.net/forums/f97/)
-   -   Toterhome Update (https://www.truckconversion.net/forums/f97/toterhome-update-5985/)

mmmc101 02-13-2011 11:47 AM

Toterhome Update
 
3 Attachment(s)
Just got the Truck back frome the paint shop. Built and installed generator and battery box. Completed framing in slideouts. The box is sitting on my homemade roll around stand for ease of construction. Received the slideout assy's from Liftco. I like the looks of the slideouts but their installation instructions are very poor. They could use a good technical writer. Just have to figure them out. Installing the sheet metal on the front of the box next so can put the box back on the truck. MMM

Bob86ZZ4 02-13-2011 03:27 PM

Looks great.

hot rod 02-15-2011 11:13 PM

You mentioned on my thread you were working on a similar project as I am, and you are definitely right. Mine won't be as complicated with the slides though, and a little lighter duty on my GMC 6500 chassis. Same toterhome setup though. Most of the other guys on there are doing full length truck conversions and have room to burn compared to us. Looks like you are making good progress. I seem to recognize the shop in the background from crawling on the web sometime back, do you have some other pics posted where I can get a look? Particularly interested in the box framework as it looks like you already did what I have planned out. Looks like you used 2x2 square tubing walls and roof? and 2x3 along the bottom? what about the main rails on top of the truck chassis? Any help appreciated.

Thanks! Dave

mmmc101 02-16-2011 08:46 AM

Dave,
Look under the forum heading "Coach in the making", thread is framing the outer walls.Those pictures were from a few months back. The box and bed were on the truck for a "clearance check" since I built them off the truck.

The floor is 2x4 11ga outer frame,floor joist are 2x3 11ga,walls and roof are 2x2 14 ga, roof outer frame 2x3 14ga. Skirts/toolboxes are 1.5 x 1.5 14ga. The box and bed have two 3x3 x .375 angle iron welded to the floor frame. The angle sits on top of mounts on the truck just like the factory sleepers are mounted . The box has six mounts and the bed has four. The mounts have rubber bushings that allow for frame twist and help isolate road vibrations. Most of the Toter's I looked at used a 1x4 on top of the truck frame rail and u-bolts like utility boxes are mounted. That also allows for frame twist. I just liked the way the factory mounted the sleeper. Just do not bolt it directly to the frame as it will shear the bolts or brake the mount. My neighbor has a factory built toter similar to what I am building.The 14ft box is bolted directly to the frame. At least twice a year he brings it over to replace the sheared bolts or reweld the mounts. The company that built it is no longer exists. I'll try to get a picture of the mounts posted.
Michael

hot rod 02-16-2011 03:33 PM

Michael-

Thanks, I'll find that thread. I know I have run across it in the past, but could not find it again. I was planning on the U-bolt and wood (or composite) insulator method. Always worked well on our truck bodies on our medium duty delivery trucks. And simple. Your tubing sizes are pretty much what I had in mind, but a little heavier in places. I guess you can't make it too strong, and you have the chassis where a few extra pounds aren't going to be noticed. Plus I'm guessing you are compensating somewhat for the big ass holes where your slides are going.

Thanks again.

Dave

mmmc101 03-21-2012 06:12 PM

4 Attachment(s)
Another update. After six months off to help a friend build a new house I am again making progress. All wiring installed. FRP installed on inside walls. Front and rear skins installed. Need to skin the sides and install the roof next. Then build and install slideouts. I now fully understand what "Engineering on the Fly" means. Wife says it must be finished and debugged before she retires next year. MMM

Dragonslayer140 03-21-2012 10:19 PM

Good to see you posting progress again, its looking really good, just need to add about another 20 feet to the box and you can drop it off at my place..lol.

Dave


All times are GMT -5. The time now is 04:47 AM.

Powered by vBulletin® Version 3.8.8 Beta 1
Copyright ©2000 - 2024, vBulletin Solutions, Inc.